Things that move on earth and in the sky depend on spinning axles that turn propellers or wheels. A propeller defines as wings arranged concentrically about an axis that when spun create thrust in an aqueous or ethereal media. Multitudes of propellers known also as impellers form the basis of turbofan jet engines. Propellers move turboprop and reciprocating engine airplanes by pushing air backwards to create thrust while the wings provide lift.
Propellers parameters are: number of blades, radius of blades, angle of blade to hub, blade width, and minimally, propeller blade style and design.
The number of blades
The more blades a propeller has, the more efficiently it pushes air up to a point. When the number of blades exceeds a certain value at a given rpm, the leading edge encounters turbulent air instead of still air and the amount of thrust does not increase any more. In a single engine aircraft with front mounted engine, the maximum number of blades acceptable does not exceed six. Above six blades on a hub, the pilot cannot see through the spinning blades.
Radius of blades
The larger the propeller, the more air it pushes. The effect of radius dramatically impacts total air mass pushed according to the relation: tangential area of propulsion equals the radius of the blades squared times pi, times the total rotations per minute of the hub. From this relation, mathematicians see the logarithmic increase in air mass pushed as a function of the square of the radius. In other words, a big propeller of radius x pushes more air then a small propeller of radius one half x moving at twice the rpm. The rate limiting factor other then hub torque of engine is how large can a propeller be before it starts hitting everything around it or in its path.
Angle of blade to hub
In a wing, the maximum lift generates at an angle of twenty degrees! In a propeller moving at a tangential velocity greater than the speed of sound, the maximum angle of efficiency becomes twenty degrees of inclination. Higher angle rates create excessive drag (parasite drag) and slow hub speed. In other words the graph of air mass pushed at high velocity levels out after twenty degrees. At slower prop speeds when the tangential velocity of the propeller is less than the speed of sound, angles up to forty five degrees can be employed with thirty degrees being the most efficient in terms of lift to drag.
Special cases: in water where the molecules bind together with hydrogen bonding, creating hyper viscosity, a higher angle of lift can employ because of lower hub rpm factors. In hypersonic aircraft, air moving at greater than the speed of sound becomes viscous due to van der wals interactions of gases and different radius and angle configurations must be taken into account. At hypersonic speeds, smaller-radius blades with extreme angles with narrower aspect configure as impeller design in turbine engines.
Blade width
The wider the propeller blade, the greater the laminar flow friction and the resulting parasite drag. The effect becomes more pronounced in a logarithmic fashion the faster the wing moves. The total force effects of blade width become extreme at tangential velocities greater than the speed of sound. Below the speed of sound blade width effects can be considered negligible. This translates into a wide blade for most applications and a narrow blade for hypersonic impellers in turbine engines and leading edges of propeller driven combat aircraft.
Special cases: in water where hyper viscosity effects retard hub rpm and tangential velocity, a wide blade of larger angle functions optimally at low hub speeds and a narrower blade of lower angle function optimally in propellers on nuclear attack submarines.
Blade design and style
Generally speaking, a wing style of propeller blade from candy bar to swept wing works the best. In a hub where all moving radius turns at a tangential velocity greater than the speed of sound, a jet aircraft style blade generates maximum thrust, minimal drag, and minimal laminar flow disturbance leading to parasite drag and eddy effects. Scimitar style blades work optimally in water where hyper viscosity of medium retard maximum hub rpm. In water, a scimitar style blade with less of an attack angle function optimally in a blade moving at less than the tangential velocity of the speed of sound. Flower design styles function optimally as impellors rather than propellers.
Conclusion
This essay portrays a macroscopic analysis of design as doe’s macroeconomics in the study of business. For microscopic and microeconomic concepts relevant to propeller design, consult the essay on the design of wings for airplanes and supersonic aircraft. She looks so nice after she showers.
References: AERODYNAMICS by the aeronautics man with a nickname. The small book can be digested in a week so look it up yourself!